Bell expressvue HD 9241

2012 · 7 replies · General

This discussion is 14 years old. It predates today's Roomie Remote X, and the app names, menus, features, pricing, and device details below have changed substantially since 2012. Treat it as historical reference — see Support and current compatibility for how things work today.

In short

Question: Hi , I need the code for my Bell Expressvue\r Satellite PVR HD . I cannot control my Bell\r PVR BOX.\r Thanks,\r Steve

Answer: Hi,\r \r Good news for Bell ExpressVu PVR code issue !!!\r Roomie apps accept only the first 4 Remote Address from your Satellite PVR...\r By default, most of Satellite PVR Receiver have a range of 1 to 16 remote address number.\r \r Here is the solution:\r Take your Satellite receiver remote control (DISH or Bell) and then,\r \r 1. Press the SYSTEM INFO on the Satellite receiver and note the Remote Address number\r 2. Press and hold the SAT Mode button until all Mode buttons light up\r 3. Enter a number between 1 to 4 ONLY, keep pointing the remote towards\r the receiver\r 4. Press Pound # (SAT mode button will flash)\r 5. Press RECORD\r 6. Press SELECT\r ......there you go.\r 7. Use the same Remote Address on the Roomie apps.\r device -> Satellite -> Bell -> All Models IP Address 1 to 4\r \r Make sure the Primary Remote Address has been changed on you're receiver.\r \r Thanks,\r Steve

Question 2012-04 · older version

Hi , I need the code for my Bell Expressvue

Satellite PVR HD . I cannot control my Bell

PVR BOX.

Thanks,

Steve

Roomie Staff 2012-04 · older version

Select your iTach, then category Satellite, then brand Bell.

Member 2012-04 · older version

Hi,

I have tried the whole 4 different options. None

of them works with my two receivers.

My first bell Expressvue is a 5900 and my

second PVR is an HD 9241 bell receiver?

Thanks,

Steve

Roomie Staff 2012-04 · older version

The codes do work with those boxes. We have a diagnostic FAQ here which should help resolve it. Most likely, you just need to increase the Retransmit Count or adjust emitter/blaster:

roomieremote.com/faq/#diagnoseIR

Member 2012-04 · older version

Hi,

I'll tell you all the steps that I tried:

add device -> Satellite -> Bell -> All Models IP Address 1 to 4

I also changed the Retransmit Count from 1 to 5 for each Models IP ....

I'm using the Blaster on port 3 and I also change the configuration to

IR Blaster from the WEB interface ??? Still not working with my

Bell Expressvue PVR HD 9241 ??? and 5900 ????

Please help, everything else works as expected.

Thanks,

Steve

Member 2012-05 · older version

Hi,

Good news for Bell ExpressVu PVR code issue !!!

Roomie apps accept only the first 4 Remote Address from your Satellite PVR...

By default, most of Satellite PVR Receiver have a range of 1 to 16 remote address number.

Here is the solution:

Take your Satellite receiver remote control (DISH or Bell) and then,

1. Press the SYSTEM INFO on the Satellite receiver and note the Remote Address number

2. Press and hold the SAT Mode button until all Mode buttons light up

3. Enter a number between 1 to 4 ONLY, keep pointing the remote towards

the receiver

4. Press Pound # (SAT mode button will flash)

5. Press RECORD

6. Press SELECT

......there you go.

7. Use the same Remote Address on the Roomie apps.

device -> Satellite -> Bell -> All Models IP Address 1 to 4

Make sure the Primary Remote Address has been changed on you're receiver.

Thanks,

Steve

Member 2012-05 · older version

I have set up the satellite remote and it is working. The problem I'm experiencing is the box will go into standby screen and you have to push the "select" button to activate the box. The universal remote i set up does not appear to have a "select" buttom control.

Thank you, Robert

Member 2012-11 · older version

1. So can we conclude that Roomie operates Bell Expressvu satisfactorily?

2. Will Roomie allow to operate the Bell Guide from the TV screen, not just viewing on IPad or IPHone?

← PreviousPort-ta / ClearMax (?) 5 to 1 HDMI Switcher Next →BT Vision box by Pace

Related threads

Today's Roomie controls 400,000+ devices.

Roomie Remote X brings TVs, receivers, streamers, lights, and whole-home audio into one app on iPhone, iPad, Mac, and Apple TV.

Download Roomie Remote X